@article {webb_optimizing_2023,
	title = {Optimizing Ocean Bottom Seismometers for Shallow Water Using Shielding and Horizontal Pressure Gradient Data},
	journal = {Journal of Geophysical Research: Solid Earth},
	volume = {128},
	number = {8},
	year = {2023},
	note = {_eprint: https://onlinelibrary.wiley.com/doi/pdf/10.1029/2023JB026356},
	pages = {e2023JB026356},
	abstract = {We show large {\textquotedblleft}shields{\textquotedblright} can significantly reduce horizontal component noise levels for ocean bottom seismometers by shielding the seismic sensors from shaking due to ocean currents. However, at short period (<1 s) some noise from vibration or rocking of the shield under current can partly couple through the ground causing peaks in the noise spectra. Deformation of the seafloor under ocean wave loading ({\textquotedblleft}compliance{\textquotedblright}) raises noise levels at long period (>5 s) for both vertical and horizontal components at shallow water sites. Pressure gauge data is now routinely used to predict and remove this source of noise on vertical component data. We have developed horizontal pressure gradient (HPG) gauges to measure and remove this source of noise from horizontal component data. The combination of HPG data and shielding enables low noise long period seismic observations at otherwise very noisy shallow seafloor sites.},
	keywords = {instrumentation, seafloor, seismology},
	issn = {2169-9356},
	doi = {10.1029/2023JB026356},
	url = {https://onlinelibrary.wiley.com/doi/abs/10.1029/2023JB026356},
	author = {Webb, Spahr C. and Barclay, Andrew H.}
}
@article {iwasaki_continuous_2022,
	title = {Continuous Tremor Activity With Stable Polarization Direction Following the 2014 Large Slow Slip Event in the Hikurangi Subduction Margin Offshore New Zealand},
	journal = {Journal of Geophysical Research: Solid Earth},
	volume = {127},
	number = {2},
	year = {2022},
	note = {_eprint: https://agupubs.onlinelibrary.wiley.com/doi/pdf/10.1029/2021JB022161},
	month = {11/2021},
	pages = {e2021JB022161},
	abstract = {Many types of slow earthquakes have been discovered at subduction zones around the world. However, the physical process of these slow earthquakes is not well understood. To monitor offshore slow earthquakes, a marine seismic and geodetic experiment was conducted at the Hikurangi subduction margin from May 2014 to June 2015. During this experiment, a large slow slip event (Mw 6.8) occurred directly beneath the ocean bottom seismometer (OBS) network. In this study, S-wave splitting and polarization analysis methods, which have been previously used on onshore data to investigate tremor and anisotropy, are applied to continuous OBS waveform data to identify tremors that are too small to detect by the envelope cross correlation method. Continuous tremor activity with stable polarization directions is detected at the end of the 2014 slow slip event and continued for about 2 weeks. The tremors are generated around a southwest bend in the slow slip contours and at the landward edge of a subducted seamount. Our findings corroborate a previous interpretation, based on burst-type repeating earthquakes and intermittent tremor, that localized slow slip and tremor around the seamount was triggered by fluid migration following the large plate boundary slow slip event and indicate tremor occurred continuously rather than as isolated and sporadic individual events.},
	keywords = {New Zealand, polarization, S-wave splitting, Seamount, slow slip, tremor},
	issn = {2169-9356},
	doi = {10.1029/2021JB022161},
	url = {https://onlinelibrary.wiley.com/doi/abs/10.1029/2021JB022161},
	author = {Iwasaki, Yuriko and Mochizuki, Kimihiro and Ishise, Motoko and Todd, Erin K. and Schwartz, Susan Y. and Zal, Hubert and Savage, Martha K. and Henrys, Stuart and Sheehan, Anne F. and Ito, Yoshihiro and Wallace, Laura M. and Webb, Spahr C. and Yamada, Tomoaki and Shinohara, Masanao}
}
@article {carchedi_investigating_2022,
	title = {Investigating Short-Period Lake-Generated Microseisms Using a Broadband Array of Onshore and Lake-Bottom Seismometers},
	journal = {Seismological Research Letters},
	volume = {93},
	number = {3},
	year = {2022},
	month = {02/2022},
	pages = {1585{\textendash}1600},
	abstract = {Recent analyses of ambient seismic noise proximal to large lakes identify excitations between periods of 0.5 and 5~s as lake-generated microseisms, though the mechanisms producing them remain unclear in the absence of distinct spectral peaks. We present a unique data set combining onshore and offshore seismometers to investigate the dominant parameters controlling water-to-solid-earth seismic coupling in a lacustrine environment. Using a set of broadband observations that include six lake-bottom seismometers, we compare signals collected both within and around Lake Malawi (Nyasa) in southeastern Africa, the fifth largest freshwater lake in the world. We document clear evidence for two peaks within the lake microseism band, with pervasive diurnal excitations between periods of \~{}0.6{\textendash}1.3 and \~{}1.3{\textendash}3~s. Variations in spectral behavior as a function of recording depth and proximity to both steep lake-floor slopes and the shoreline suggest that the spectral bands may correspond to single- and double-frequency generation processes, akin to primary and secondary ocean microseisms generated by the shoaling of wind-driven gravity waves along shorelines and wave interactions within the open body of water, respectively. However, both the absolute amplitudes and temporal evolution we observe in these two bands are complex and often inconsistent with traditional microseism theory. Therefore, these spectral bands may alternatively result from complex wave{\textendash}wave interaction at the lake surface within the enclosed northern end of the lake. The diurnal behavior of lake microseisms, as well as their polarizations, suggest that the wave energy is driven by a combination of seasonally varying nighttime winds funneled by lakeshore topography and waveguide effects. This work also provides a glimpse into seasonal variation in lacustrine ambient seismic noise and thus also into lake processes.},
	issn = {0895-0695},
	doi = {10.1785/0220210155},
	url = {https://doi.org/10.1785/0220210155},
	author = {Carchedi, Christopher James William and Gaherty, James B. and Webb, Spahr C. and Shillington, Donna J.}
}
@article {li_connections_2018,
	title = {Connections between subducted sediment, pore-fluid pressure, and earthquake behavior along the Alaska megathrust},
	journal = {Geology},
	volume = {46},
	number = {4},
	year = {2018},
	month = {02/2018},
	pages = {299{\textendash}302},
	abstract = {Variations in pore-fluid pressure along subduction megathrusts are often invoked to explain differences in fault slip behavior between margins. However, many other parameters vary between subduction zones, making it difficult to isolate the causes of elevated pore fluid pressures and their effects on megathrust behavior. Here we show evidence from pre-stack depth migrations of multichannel seismic reflection data along the subduction zone off the Alaska Peninsula for significant, systematic along-strike variations in the thickness, continuity, P-wave velocity, and estimated pore-fluid pressure of the subducting sediment layer that lines the shallow plate interface within 25 km of the trench. These variations appear to correlate with changes in seismicity, locking, and earthquake rupture history. The currently locked and seismically quiet Semidi segment has a continuous, thick (600{\textendash}900 m) subducted sediment layer that is characterized by low seismic velocities and elevated pore pressure (λ* ≈ 0.4{\textendash}0.8). The subducted sediment in the neighboring Shumagin Gap, a region with low geodetic coupling and abundant small earthquakes, is thinner, irregular and has lower pore pressure (λ* \&lt; 0.2{\textendash}0.3). We suggest that the thicker and weakly faulted sediment layer entering the trench at Semidi is associated with a continuous and overpressured sediment layer lining the shallow plate interface, but forms a large coherent asperity as it dewaters and consolidates at greater depths, thus favoring large earthquakes. In contrast, thinner incoming sediment disrupted by outer rise faulting at Shumagin results in a plate interface without elevated pore-fluid pressures, but which is heterogeneous and complex at all depths, contributing to creep and frequent small earthquakes.},
	issn = {0091-7613},
	doi = {10.1130/G39557.1},
	url = {https://doi.org/10.1130/G39557.1},
	author = {Li, Jiyao and Shillington, Donna J. and Saffer, Demian M. and B{\'e}cel, Anne and Nedimovi{\'c}, Mladen R. and Kuehn, Harold and Webb, Spahr C. and Keranen, Katie M. and Abers, Geoffrey A.}
}
@article {todd_earthquakes_2018,
	title = {Earthquakes and Tremor Linked to Seamount Subduction During Shallow Slow Slip at the Hikurangi Margin, New Zealand},
	journal = {Journal of Geophysical Research: Solid Earth},
	volume = {123},
	number = {8},
	year = {2018},
	note = {_eprint: https://agupubs.onlinelibrary.wiley.com/doi/pdf/10.1029/2018JB016136},
	pages = {6769{\textendash}6783},
	abstract = {Shallow slow slip events have been well documented offshore Gisborne at the northern Hikurangi subduction margin, New Zealand, and are associated with tectonic tremor downdip of the slow slip patch and increases in local microseismicity. Tremor and seismicity on the shallow subduction interface are often poorly resolved due to their distance from land-based seismic and geodetic networks. To address this shortcoming, the Hikurangi Ocean Bottom Investigation of Tremor and Slow Slip experiment deployed 24 absolute pressure gauges and 15 ocean bottom seismometers on the seafloor above the Gisborne slow slip patch to investigate the spatial and temporal extent of slow slip and associated tremor and earthquake activity. We present a detailed spatiotemporal analysis of the seismic signatures of various interplate slip processes associated with the September/October 2014 Gisborne slow slip event. Tectonic tremor begins toward the end and continues after the geodetically constrained slow slip event and is localized in the vicinity of two subducted seamounts within and updip of the slow slip patch. The subsequent, rather than synchronous occurrence of tremor suggests that tremor may be triggered by stress changes induced by slow slip. However, Coulomb failure stress change models based on the slow slip distribution fail to predict the location of tremor, suggesting that seamount subduction plays a dominant role in the stress state of the shallow megathrust. This and the observed interplay of seismic and aseismic interplate slip processes imply that stress changes from slow slip play a secondary role in the distribution of associated microseismicity.},
	keywords = {earthquake, New Zealand, Seamount, slow slip, subduction, tremor},
	issn = {2169-9356},
	doi = {10.1029/2018JB016136},
	url = {https://onlinelibrary.wiley.com/doi/abs/10.1029/2018JB016136},
	author = {Todd, Erin K. and Schwartz, Susan Y. and Mochizuki, Kimihiro and Wallace, Laura M. and Sheehan, Anne F. and Webb, Spahr C. and Williams, Charles A. and Nakai, Jenny and Yarce, Jefferson and Fry, Bill and Henrys, Stuart and Ito, Yoshihiro}
}
@article {becel_tsunamigenic_2017,
	title = {Tsunamigenic structures in a creeping section of the Alaska subduction zone},
	journal = {Nature Geoscience},
	volume = {10},
	number = {8},
	year = {2017},
	note = {Publisher: Nature Publishing Group},
	pages = {609{\textendash}613},
	abstract = {Segments of subduction zones that are capable of generating tsunamigenic earthquakes appear to have characteristic structural configurations. These structures include heterogeneous plate interfaces, a small wedge of deformed sediment at the toe of the overriding plate (the frontal prism), and splay faults in the crust of the overriding plate that root within the plate boundary megathrust. Here we use seismic reflection imaging to show that these features also exist within a creeping segment of the Alaska subduction zone, the Shumagin Gap. We identify an active crustal-scale normal fault system that dips landward and resembles that involved in the 2011 Tohoku-oki earthquake in Japan. We also find that the Shumagin Gap has a small frontal prism, a deep-water splay fault, and that the plate interface here is rough and thinly sedimented. We propose that lateral propagation of rupture from a neighbouring segment into the Shumagin Gap may explain a tsunamigenic earthquake that occurred there in 1788 and that tsunamigenic potential should be considered in hazard assessments for the region. Our results demonstrate that structural configurations similar to those in Tohoku may exist in other subduction zones, including within creeping segments or segments with no record of historical megathrust earthquakes, but are under-recognized. Identifying similar configurations globally may improve our ability to anticipate regions capable of generating large tsunamis.},
	keywords = {Geodynamics, Geology, Natural hazards, seismology, Tectonics},
	issn = {1752-0908},
	doi = {10.1038/ngeo2990},
	url = {https://www.nature.com/articles/ngeo2990},
	author = {B{\'e}cel, Anne and Shillington, Donna J. and Delescluse, Matthias and Nedimovi{\'c}, Mladen R. and Abers, Geoffrey A. and Saffer, Demian M. and Webb, Spahr C. and Keranen, Katie M. and Roche, Pierre-Henri and Li, Jiyao and Kuehn, Harold}
}
@article {webb_high-resolution_2016,
	title = {High-Resolution Seafloor Absolute Pressure Gauge Measurements Using a Better Counting Method},
	journal = {Journal of Atmospheric and Oceanic Technology},
	volume = {33},
	number = {9},
	year = {2016},
	note = {Publisher: American Meteorological Society Section: Journal of Atmospheric and Oceanic Technology},
	month = {sep},
	pages = {1859{\textendash}1874},
	abstract = {Abstract Vibrating quartz force transducers are the critical component of most deep-sea pressure and depth gauges in use in oceanography, producing a frequency output that varies with pressure. Accurate and low drift pressure measurements can be obtained by precisely measuring this frequency. In most implementations, the frequency is determined by counting the number of cycles of a high-frequency standard oscillator occurring during a large number of cycles of the lower-frequency quartz force oscillator. Resolution is limited by the sampling interval (length of counting) and the frequency of the frequency standard. Alternative counting methods can provide significant (20{\textendash}40 dB) improvements in resolution at sampling rates above 1 Hz. Each counting method can be described as a different filter applied to the output of a counter of the frequency standard gated at each transition of the transducer quartz oscillator. Improvements in resolution can be understood as the result of minimizing the aliasing of higher-frequency counting noise into the spectrum below the Nyquist frequency. A simple multipole infinite impulse response (IIR) filter designed to limit spectral leakage of high-frequency noise minimizes the noise spectrum and thereby optimizes the resolution of the pressure output. The resultant noise spectrum rises as frequency squared above 1 Hz, independent of the sampling rate. At frequencies below 1 Hz, it is limited by noise in the electronics driving the force transducer quartz oscillator. Resolution increases with frequency of the frequency standard up to about 200 MHz, plateauing for higher frequencies due to other noise sources (likely electronic).},
	issn = {0739-0572, 1520-0426},
	doi = {10.1175/JTECH-D-15-0114.1},
	url = {https://journals.ametsoc.org/view/journals/atot/33/9/jtech-d-15-0114_1.xml},
	author = {Webb, Spahr C. and Nooner, Scott L.}
}
@article {Wei2016,
	title = {Upper mantle structure of the Tonga-Lau-Fiji region from Rayleigh wave tomography},
	journal = {Geochemistry, Geophysics, Geosystems},
	volume = {17},
	number = {11},
	year = {2016},
	month = {nov},
	pages = {4705{\textendash}4724},
	issn = {15252027},
	doi = {10.1002/2016GC006656},
	url = {http://doi.wiley.com/10.1002/2016GC006656},
	author = {Wei, S. Shawn and Zha, Yang and Shen, Weisen and Wiens, Douglas A. and Conder, James A. and Webb, Spahr C.}
}
@article {shillington_link_2015,
	title = {Link between plate fabric, hydration and subduction zone seismicity in Alaska},
	journal = {Nature Geoscience},
	volume = {8},
	number = {12},
	year = {2015},
	note = {Publisher: Nature Publishing Group},
	pages = {961{\textendash}964},
	abstract = {Subduction carries water into the Earth where it can influence seismicity. Analysis of the structure of the Alaskan subduction zone suggests fluid delivery is influenced by faults in the oceanic plate that formed at the mid-ocean ridge.},
	keywords = {Geodynamics, seismology, Tectonics},
	issn = {1752-0908},
	doi = {10.1038/ngeo2586},
	url = {https://www.nature.com/articles/ngeo2586},
	author = {Shillington, Donna J. and B{\'e}cel, Anne and Nedimovi{\'c}, Mladen R. and Kuehn, Harold and Webb, Spahr C. and Abers, Geoffrey A. and Keranen, Katie M. and Li, Jiyao and Delescluse, Matthias and Mattei-Salicrup, Gabriel A.}
}
@article {Becel2015,
	title = {Origin of dipping structures in fast-spreading oceanic lower crust offshore Alaska imaged by multichannel seismic data},
	journal = {Earth and Planetary Science Letters},
	volume = {424},
	year = {2015},
	month = {aug},
	pages = {26{\textendash}37},
	issn = {0012821X},
	doi = {10.1016/j.epsl.2015.05.016},
	url = {https://linkinghub.elsevier.com/retrieve/pii/S0012821X15003052},
	author = {B{\'e}cel, Anne and Shillington, Donna J. and Nedimovi{\'c}, Mladen R. and Webb, Spahr C. and Kuehn, Harold}
}
@article {Menke2015,
	title = {Seismic anisotropy indicates ridge-parallel asthenospheric flow beneath the Eastern Lau Spreading Center},
	journal = {Journal of Geophysical Research: Solid Earth},
	volume = {120},
	number = {2},
	year = {2015},
	month = {feb},
	pages = {976{\textendash}992},
	issn = {2169-9313},
	doi = {10.1002/2014JB011154},
	url = {https://onlinelibrary.wiley.com/doi/abs/10.1002/2014JB011154},
	author = {Menke, William and Zha, Yang and Webb, Spahr C. and Blackman, Donna K.}
}
@article {Wei2015,
	title = {Seismic evidence of effects of water on melt transport in the Lau back-arc mantle},
	journal = {Nature},
	volume = {518},
	number = {7539},
	year = {2015},
	month = {feb},
	pages = {395{\textendash}398},
	issn = {0028-0836},
	doi = {10.1038/nature14113},
	url = {http://www.nature.com/articles/nature14113},
	author = {Wei, S. Shawn and Wiens, Douglas A. and Zha, Yang and Plank, Terry and Webb, Spahr C. and Blackman, Donna K. and Dunn, Robert A. and Conder, James A.}
}
